Silent metering fuel pump for Air 4D, 8D, 9D & Flow 14D. Voltage: 12V / 100 tick dose: 6.8 ml.
In StockVoltage: 12V Thermal power: 1700W Airflow: 110 m3 / h Power consumption: 7W Fan noise: 48 db Hot water pipe: 16mm Weight: 1 kg
In StockFuel pump for heater Eberspacher. Voltage: 12V. Flows: 22mm3.Diesel or gasoline.Fits the following heaters:Eberspacher: Airtronic D2/D4.
In StockTemperature and overheat sensor for AUTOTERM Air 4D.
In StockIt is intended for installation inside DUCATO/BOXER/JUMPER vehicles, under the passengers seat. The material is zinc.
In StockGlow plug bushing gasket for AUTOTERM Air 2D, 4D & Flow 5.
In StockFlame indicator / Overheat sensor for Planar 3 kW.
In StockTemperature and overheat sensor for AUTOTERM Air 2D. Suitable for all modifications of air heaters AUTOTERM Air 2D, that produced till November 2016.
In StockFuel: Diesel, For AUTOTERM Air 4D
In StockWiring for control panel, for PU-5, PU-27, Comfort Control.
In StockExternal Ø16mm. Material PA 6.6 + 30 FV. Electrical Power 3 W. Weight 0.200 kg. Differential pressure 1 bar. Range Fluid temperature -20 / +100 ° C.
In StockNylon fuel line. 10 meters. For Air 2D, 4D, 8D, 9D & Flow 5.
In StockGlow plug evaporation screen for AUTOTERM Air 8D, 9D & Flow 14D.
In StockUSB adapter for diagnostic equipment, designed for connecting liquid heaters and air heaters to a personal computer. It is applied to obtain data about the status of the heater or to make a heater diagnostic.
In StockThe bushing for the combustion chamber screen. For one screen 3 bushings are needed. The bushing for the combustion chamber screen is suitable for all modifications of the following air heaters: AUTOTERM Air 2D.
In StockFuel pump cable, for all AUTOTERM Air heaters.
In StockVoltage: 12V The degree of control: 3 Thermal power: 4.25 kW Fan noise: 65 db Air flow: 195 m3 / h The fan power: 50 W Hot water pipe: Ø 16 mm Weight: 1.5 kg
In StockCombustion chamber, suitable for all modifications of air heaters AUTOTERM Air 2D. Glow plug evaporation screen (SB.869) included.
In StockThis wire is compatible only with the Comfort Control panel.
In StockThe heater Teplostar is designed for heating of liquids and can be used for the purposes below: - For heating the engines of trucks and buses - For heating the floors (ex. trailers, caravans) - For heating the air indoors with the help of radiators. The kit is meant for wheeled tractors and other vehicles with...
In StockThe heating device is independent heating unit that consists of: -heater 8kW;-fuel pump;-exhaust pipe Ø38mm (1 meter);-cable for pump;-cabel for control panel (1,8 meter)-cable for battery(6,5 meter )-fuel standpipe;-T-fuel tube;-tank 7l. It is the most effective solution for heating of cargo spaces for transport of goods sensitive...
In StockThe heating device is independent heating unit that consists of: -heater 8kW;-fuel pump;-exhaust pipe Ø38mm (1 meter);-cable for pump;-cabel for control panel (1,8 meter)-cable for battery(6,5 meter )-fuel standpipe;-T-fuel tube;-tank 7l. It is the most effective solution for heating of cargo spaces for transport of goods sensitive...
In StockGasket repair kit, suitable for the following heaters: AUTOTERM Flow 14D / Teplostar 14 + 14TS (mini).
In StockSilent metering fuel pump for Air 4D, 8D ,9D & Flow14D. Voltage: 24V /100 tick dose: 6.8 ml.
In StockFuel pump for heater Webasto. Voltage: 24V. Flows: 65mm3.Diesel or gasoline.Fits the following heaters:Thermo Top E, C, P, Z (Webasto);Thermo Top Evo (Webasto);Air Top (Webasto).
In StockThe heater Teplostar is designed for heating of liquids and can be used for the purposes below: - For heating the engines of trucks and buses - For heating the floors (ex. trailers, caravans) - For heating the air indoors with the help of radiators. The kit is meant for wheeled tractors and other vehicles with...
In StockGasket repair kit, suitable for all modifications of air heaters AUTOTERM Air 2D.
In StockHeater 2kW(MOUNTAIN KIT) 12V + silent fuel pump (TH-11)
In StockBattery cable for Planar 2D, 4D, 44D.
In StockGasket repair kit, suitable for all the following liquid heater modifications: AUTOTERM Flow 5D / 5B.
Grille for casing, suitable for all following air heaters: AUTOTERM Air 2D.
In StockAir pump assy.5564 for AUTOTERM Air 2D 12V heater. This 12V air pump is compatible with AUTOTERM Air 2D heaters equipped with the following control units (assy numbers): 5563 6268Suitable for heaters with the following serial numbers:5561xxxxxxx 6266xxxxxxx
In Stock12V or 24V.Diesel or gasoline.Fits independent heating:Thermo Top E, C, P, Z -Air Top 2000 STCThermo Top Evo Start (5 kW)Thermo Top Evo Comfort + (5kW)Thermo Pro 50Thermo Pro 90Air Top Evo 40 B / DAir Top Evo 55 B / D
In StockGasket repair kit. Suitable for all modifications of air heaters PLANAR 4D.
In StockVoltage: 24V / For AUTOTERM Air 4D
In StockFlame indicator / Overheat sensor for AUTOTERM Air 4D
In StockSilent metering fuel pump. Suitable for Air 2D & Flow 5D / 5B. 100 tick dose: 4.4 ml. Voltage: 24V.
In StockRubber seal/holder for fuel pipe. The mounting seal is suitable for AUTOTERM Air 2D.
In StockHigh altitude control unit, for AUTOTERM Air 4D. Voltage: 12V
In StockThe heating unit Binar 5 for pre-heating of engines before their starting was developed for installation in passenger cars and designed for:heating of engines for safe putting them into operation at low temperatures; heating of cabins and front glass/windshield (for deicing) when the engine is stopped; additional heating of the...
In StockHeat exchanger, suitable for all the following air heater modifications: AUTOTERM Air 2D.
In StockCombustion chamber, suitable for all the modifications of the liquid heaters AUTOTERM Flow 14D / Teplostar 14. Fuel: Diesel.
In StockGlow plug suitable for all modifications of the following air heater with voltage - 24V: AUTOTERM Air 2D. Voltage: 24V.
In StockVoltage 12V. Ø 16mm. Pressure 2,5 bars. Electrical power 20W. Fluid temperature range -40/+100 °C. Flow 900 l/h. Weight 0,530 kg.
In StockThe heating device is independent heating unit that consists of: -heater 2kW (MOUNTAIN KIT),-silent fuel pump;-exhaust pipe Ø24mm (1 meter);-isolation (0,45 meter);-exhaust silencer;-cable for pump;-cabel for control panel (1,8 meter)-cable for battery(6,5 meter )-tank 7L. This kind of a heater is on sale in a set together with a...
In StockFlame indicator / Overheat sensor, suitable for all the following heaters: AUTOTERM Flow 5D / 5B.
In StockGlow plug, suitable only for the following pre-heaters in voltage 12V: AUTOTERM Flow 5D / 5B. Voltage: 12V.
In StockAir pump, suitable for all the following liquid heaters with 12V modifications: AUTOTERM Flow 5D / 5B. Voltage: 12V.
In StockFuel pump for heater Eberspacher. Voltage: 12V.Flows: 45mm3.Fits the following heaters:Eberspacher: Hydronic 10kW.
In StockFuel pump for heater Eberspacher. Voltage: 24V.Flows: 45mm3.Fits the following heaters:Eberspacher: Hydronic 10kW.
In StockFlange Ø 90mm, assy.P4942 Please note, that flange and deflector or grille are different spare parts and deflector should be ordered separately. If you buy P4942 you will need to buy P4944 grille or 4108 deflector Material: PA6 plastics
In StockCoolant inlet/outlet repair kit, suitable for liquid heater AUTOTERM Flow 5.
In StockThis connector is suitable for the following control panels: PU-5 (assy.3765)PU-22 (assy.3355)PU-27 (assy.4725)Comfort Control (assy.AT0050)
In StockThe combustion chamber screen, suitable for all modifications of the following air heaters: AUTOTERM Air 2D.
In StockVoltage: 24V / For AUTOTERM Air 4D-24-GP-P-3030
In StockFlame indicator / Overheat sensor for AUTOTERM Air 8D.
In StockThis gasket repair kit is suitable for Planar / Air 9D
In StockThe heating unit Binar 5 for pre-heating of engines before their starting was developed for installation in passenger cars and designed for:-heating of engines for safe putting them into operation at low temperatures;-heating of cabins and front glass/windshield (for deicing) when the engine is stopped;-additional heating of the engine...
In StockControl Unit, suitable for pre-heaters AUTOTERM Flow 5D 12V (diesel). All AUTOTERM Flow 5D (12V) heaters with serial number series: 4826xxxxxxx are equipped with this control unit. Voltage: 12V.
In StockCasing lower part, suitable for all modifications of air heaters AUTOTERM Air 4D.
In StockVoltage: 12V / For AUTOTERM Air 4D-12-ТМ
In StockHigh altitude control unit, suitable for air heaters AUTOTERM Air 2D with a specific serial number: 5561xxxxxxx. Heater equipped with this control unit can work at altitude up to 2500 meters above sea level. Voltage: 12V.
In StockThis 12V glow plug is suitable for Planar/Air 9D 12V/24V
In StockVoltage: 24V / For AUTOTERM Air 4D
In StockVoltage: 12V / For AUTOTERM Air 4D-12-GP-ТМ
In StockCasing upper part, suitable for all modifications of air heater AUTOTERM Air 2D.
In StockThis 6cm long fuel-connecting hose is suitable for all Autoterm fuel lines. It helps to connect the nylon fuel line with the fuel standpipe or fuel pump or heater. Material: Rubber OD: 11 mm ID: 5 mm Length: 0.06 meters
In StockRepairing gasket kit. Suitable for all modifications of heaters Teplostar 14 / Teplostar 14 TS.
In StockThis 12V control unit is compatible with AIR 4D heaters equipped with the following air pump 5743Suitable for heaters with the following serial numbers: 5741xxxxxxx 6356xxxxxxxCompatible with glow plug 3333 Please note - that this control unit has the updated work algorithm on the temperature mode. This means that in temperature mode...
In StockDiameter: 38mmStainless steel grade: AISI 321 / EN 1.4541Contains: Exhaust silencer - 1 piece Clamp - 2 pieces Bolt M8 - 1 piece Nut M8 - 1 piece Lock washer 8 - 1 piece Washer 8 - 1 piece
In StockVoltage 24V. Ø 20mm. Pressure 2,5 bars. Electrical power 20W. Fluid temperature range -40/+100 °C. Flow 900 l/h. Weight 0,530 kg.
In StockCombustion chamber (diesel), suitable for modifications of the diesel engine pre-heaters AUTOTERM Flow 5D
In Stock